- 意大利Chemitec
- 意大利賽高SEKO計量泵
- 意大利SEKO儀器儀表
- 意大利SEKO氣動隔膜泵
- FLOWLINE液位計
- 瑞士梅特勒mettler
- 英國Williamson蠕動泵
- E+H
- 德國LUTZ魯茨
- 美國G+F儀表閥門控制器
- 法國（KIMO)凱茂環境測量及...
- 美國FTI插桶泵
- 進口氣動隔膜泵
- 易威奇計量泵
- 米頓羅計量泵
- 普羅名特計量泵
- 帕斯菲達計量泵
- 上泰儀器儀表
- 哈納儀器儀表
- 羅斯蒙特儀表
- Hamilton 漢密爾頓
流量：2.34L/H ，壓力：10.5Bar，美國帕斯菲達pulsafeeder機械隔膜計量泵X215加藥泵
200、250系列機械隔膜計量泵流量：2.34L/H ，壓力：10.5Bar，美國帕斯菲達pulsafeeder機械隔膜計量泵X215加藥泵
詳細介紹
*為特殊使用場所而設計之高壓計量泵 *高效率風冷式馬達，油浸式齒輪箱 *金屬增強隔膜，短距離動作沖程，壽命長 *計量**，輸出量可隨意調整 *高扭力齒輪組，確保高壓力時順利啟動運轉
流量：2.34L/H ，壓力：10.5Bar，美國帕斯菲達pulsafeeder機械隔膜計量泵X215加藥泵
Sometimes the output adjusting know can move on its shaft and cause a false output indication. This can happen if the knob set-screw slips or it the unit is disassembled for any reason. The unit can be reset to " O" follows:
1. Remove the dial stop.
2. With the pump running, loosen the locking lever and turn the adjusting knob counter-clockwise until it is "loose" to touch.
3. SLOWLY turn the knob clockwise, using very light finger pressure. It wilf soon start to advance in pulses as the internal cam comes in and out of contact.
4. When light finger pressure will no longer allow movement of the knob between cam contacts, grasp the knob securely and tighten the locking lever fturning clockwise) making sure that the knob does not move. To check for zero point, turn on pump.
There should be no liquid coming out of discharge fitting.
5. Replace dial stop.
6. If the pointer is not at "0", loosen the set-screw on the knob(use a ,078in.-Hex key), and turn pointer to u0", then re-tighten the setscrew while holding the knob in place.
7. A setting of "0" will now give zero output. One full revolution of the knob counter-clockwise will give maximum output. The knob should never be turned more than one full revolution.
